CMP-03 Solar Lighting Controller Mini Solar Charge Controller

Six types to choose:

CMP-03 3A 6V ST :3A 6V light and 8h timer control.
CMP-03 3A 12V ST:3A 12V light and 8h timer control.
CMP-03 3A 6V S:3A 6V Light Control.
CMP-03 3A 12V S: 3A 12V Light Control.
CMP-03 3A 12V:Charge & Discharge
CMP-03 3A 6V: Charge & Discharge

Package:
1. 1PCS Solar Charge Controller

Notice:This product has light and time control.
Light control:When daylight starts to occur then the light source goes off. Meanwhile the Solar Panels will charge the batteries. when there is no sunlight the garden light will switch on.
Time control:There is an eight hours time control,that means it will go off when the Lights automatically switch off after 8 hours.

Function:
1. Prevent the battery from over charging, over discharging and Reverse discharging to solar panel during nights.
2. Controller will start the lighting system in the evening automatically according to the surrounding luminance.
3. Controller can automatically shut down the lighting system:
A: Automatically shut down the light at dawn when battery is full.
B: Automatically shut down the light when battery is low.

CMP-03 Data Sheet
Model:CMP-03
Rated Voltage:DC6V,DC12V
Max Current:3A
voltage of solar panels:&S804;18W(3A,6v,12v)
Charge-stop Voltage: 7.2V
Size:55&>15;36&>15;20mm
Supply-stop Voltage:5.3V
Supply-resume Voltage:6V
Light Control Mode:Visibility 20M
Weight:33g
Notice:Sensor Control if customer need it.

CMP-03 5A 12V Solar Lighting controller IP66 Waterproof Introduction£º

The CMP-03-Series solar charge controller applies a microchip for intelligent control.The charging efficiency can be highly increased by using dual-mos charging circuit ,compared to normal diode for reserve current protection. The controller can extend the battery life with build-in 4-stage PWM charging program.It is equipped with various of protection function such as over-charge protection,over discharge protection ,over-load protection,reverse current protection.

Function:
1. Prevent the battery from over charging, over discharging and Reverse discharging to solar panel during nights.
2. Controller will start the lighting system in the evening automatically according to the surrounding luminance.
3. Controller can automatically shut down the lighting system:
A: Automatically shut down the light at dawn when battery is full.
B: Automatically shut down the light when battery is low.
Notice:This product has light and time control.
Light control:When daylight starts to occur then the light source goes off. Meanwhile the
Solar Panels will charge the batteries. when there is no sunlight the garden light will switch on. Time control:There is an eight hours time control,that means it will go off when the Lights
automatically switch off after 8 hours.

	Green(charge£©	Red£¨discharge£©
off	Solar panel disconnect /it is at night	Load output is off
on	Under PWM charge	Load output is on
Slow-flashing	Under float charge	Over load
Fast-flashing	Under buck charge	N/C

 

 

 

Data Sheet

Model	CMP-03-5A
Max charge current	5A
Max charge current	5A
Over load	About 6A
Rated battery voltage	6V
Max solar panel input voltage	10.8V
Equalize voltage	7.4V
Constant voltage	7.1V
Float voltage	6.9V
LVD	5.6V
Discharge return	6.3V
Charging control	PWM 3 stage
Standby lost	2.8mA@6V
Min start voltage	4.5V
wire	20AWG*10cm
Size/weight	60x25x18mm/50g

CMP12 CMP12/24 10A 12V 24V Solar Charge Controller

Only For off-Grid PV Solar System.
For 12V Pv System: 150W Solar Panel,12V Lead-acid Battery,21V for Max input Voltage
For 24V Pv System: 300W Solar Panel,24V Lead-acid Battery,42V for Max input Voltage

Package including:
1.1PCS 10A Solar Contorller
2.1PCS User Manual

Protection:
Overcharging protection
Can be used for all panels
Overdischarging protection
Short and Open Circuit protection
Full specification available if required
Fail Safe and cannot be damaged by accidental wiring mistakes
Advanced design with simple plug and play technology. No need for complicated adjustments

Indicator LED
1.The Battery is being charged strongly when the Charge LED is lighting;Filckering means the battery is in floating charge Mode,if it`s off means charging stopped.
2.When the LOAD LED is lighting,it means there is output and load can work;if it`s off,there isn`t output and the load can`t work.

Introduction:
A solar charge controller is the controlling center of the PV battery in off-grid power system which makes use of solar cells array to protect your batteries from being over-charge and over-discharge, so the life span of it can be extended.

Features:
Function£ºAccording to the voltage of battery, Solar charge controller will adjust the charging current and decide if to supply power to the loads.
1. Generally keep the battery on full voltage condition.
2. Prevent the battery from over-charging.
3. Prevent the battery from over-discharging.
4. Prevent the battery from supplying power to solar panels during nights.
Output voltage:12V 24V auto switch
Max load current: ¡Ü12A
Full charge cut:13.7V
Low voltage cut:10.5V
Temp ompensation:-3mv/¡æ/cell
Zero Load Loses:¡Ü20mA
Voltage Drop:<160mv

CM1012 CM1524 10A 15A Solar Charge Controller PWM

Features    
1. Intuitionist LED indicators show the current system battery capacity, charging and discharging state of the battery.  
2. Having the protection functions as overcharging, over discharging, overload, short-circuit and reversed connection.                                                                                        
3. Tandem type PWM charging makes the charging efficiency increase by 3% to 6%, compared with non-PWM charging.                                                                                               
4. The parameters of charging and discharging have been set during the production(special parameters need to be told in advance), so no need to adjust the parameters.                                                             
5. It can set the working mode of the load.                                                                
6.USB charging function (optional). 

Operation instruction 

1.Charging and display: After the controller is connected right, if the charging indicator is still not illuminating, this means the sunshine is weak or there is not sunshine.
 And if the charging indicator is  illuminating, it means the controller is charging the battery. When the indicator flickers, it means the battery enters into float charging mode,
 and this can make the  battery at full charging state to lengthen the longevity of the battery. Only when the controller detects the battery over discharging, can it start the 
hoisting charging mode. 
                                                                             
2.Battery capacity and display: When the battery indicator is red flickering, the load will shut time-delayed to protect the battery.

Battery capacity state	Full charged	normal	Low capacity	Low battery warning
indicator	green	orange	red	Red flickering

3. Load state and indicator: When the load indicator is green and flicker, the load will be shut.

Load state	starting	shutting	overload protection	short-circuit protection
indicator	green on	green off	green flickering slowly	green flickering quickly

Data sheet

Model	CM1012	CM1524	Low voltage reconnecting	12.6V/25.2V
Rated current	10A	15A	Temperature compensation	-4mv/℃/2V£¨hoisting, floating charging compensation£©
System voltage	12V/24V AUTO		Charging mode	PWM
no load loss	≤12 mA Not including USB		Weight	145g
charging (Discharging) circuit voltage drop	<0.2V(<0.15V)		Overloading and short circuit protection	1.25 times than rated current, protect the load within 60 seconds;  1.5 times than rated current, protect the load within 5 seconds.  2.5 times or over, starting the short circuit protection
Hoisting voltage	14.4V/28.8V£» (lasting time£º10min)
Float charging voltage	13.7V/27.4V		Size	130mm*75mm*37mm
Environmental temperature	-20℃―50℃		installing holes	Φ3.5—55mm*122mm
Low voltage protection	10.7V/21.4V		installing cables diameter	≤16mm2

CM20 Solar Charge Controller 12V 24V PWM

Features   
                                                                                                                                                                                                                          
1. Intuitionistic LED indicators show the current system battery capacity, charging and discharging state of the battery.                                                                                      
2. Having the protection functions as overcharging, over discharging, overload, short-circuit and reversed connection.                                                                                         
3. Tandem type PWM charging makes the charging efficiency increase by 3% to 6%, compared with non-PWM charging.                                                                                               
4.The parameters of charging and discharging have been set during the production(special parameters need to be told in advance), so no need to adjust the parameters.                                                               
5.It can set the working mode of the load.                                                                
6.USB charging function (optional).                                                                      
7. Grid-complementary(optional function)                                                                     
8. remote telecommunications function equipped(optional function).                                                
9. Prevent battery from discharging to battery at night.   

LED indicators instruction                                                                                       

icon	indicator	state	instruction
	Charging LED	off	not charging, no connecting of solar panels or weak sunshine
		on	charging, or elevated charging
		flickering	float charging, battery charged full
	Battery capacity LED	green led on	battery capacity full
		yellow led on	battery capacity normal
		red led on	battery capacity low
		red led flickering	low voltage protection for battery
	Load LED	on	load on
		off	load off
		flickering	load closed, output overload or short-circuit.

load working mode instruction and setting

1. Normal mode : controller is used as PWM charging controller without lighting and timer function. Controller is at this mode without special request.
2. Lighting and timer controlling mode: At this mode, the controller will start the load after darkness and will close the load after setting hours(or sunrise).
3. Lighting control mode: At this mode, when the solar panels voltage is lower than 2.5V(for 24V system, 5V. for 48V system, 10V), controller will start the load after 10 seconds.
When the solar panels voltage is higher then 3.5V(for 24V system, 7V. for 48V system, 14V), controller will close the load after 10 seconds.

Data Sheet

MODEL	CM2024Z	CM2048	MODEL	CM2024Z	CM2048
system voltage	12V/24V	48V	load loss	<13 mA
open circuit voltage	<50V	<100V	voltage drop of charging circuit	<0.2V
Rated charging and discharging current no	20A		voltage drop of discharging circuit	<0.1V
elevated voltage	14.4V/28.8V	57.6V	temperature compensation	-4mv/cell/℃
Float charging voltage	13.8V/27.6V	55.2V	cable diameter	<6mm2
low voltage disconnecting	11.2V/22.4V	44.8V	installing size	Φ4mm—159mm*68mm
low voltage recovery	12.6V/25.2V	50.4V	dimension	168mm*88mm*34mm
charging mode	PWM		storage temperature	-35℃ — 70℃
output overload and short-circuit protection	output >23A and 60s or  >29A and 15s overload protection or >40A short-circuit		working temperature	-25℃ — 60℃
			humidity requirement	≤90£¥
			weight	275g

CM20E 10A 20A Solar Charge Controller Metal Case

 

CM20P 20A 10A Flush Mount Controllers

 Function     
                                                                                        
1.LED indicator for battery condition, charge and discharge condition.                                           
2. Overcharge and overdischarge protection, overload and reverse connection protection.                                               
3. PWM technology                                                                  
4. Technical data charge and discharge setted.(customerized for special request)                                                                                                                                   
5. USB output.                                                                         
6. Built-in boarding installation.    

Data Sheet

MODEL	CM20P-10A	CM20P-20A		MODEL	CM20P-10A	CM20P-20A
System Volts	12V/24Vauto			HVR	15.0V	15.0V/30.0V
Rated Charge Current	10A	20A		Self consumption	≤15 mA
Rated Load Current	10A	20A		Charge Type	PWM
Charge Voltage Drop	<0.3V			Temperature Compensation	-4mv/cell/℃(customized)
Discharge Voltage Drop	<0.15V			Cable	≤6mm2
Boost Voltage	Sealed Battery 14.2V/28.4V		(keep time£º2H)	Temperature	-20℃ to +50℃
	Open Battery14.4V/28.8V			Stock	-30℃ to +60℃
	Glue Battery14.6V/29.2V			Humidity	<90%
Float Voltage	13.7V	13.7V/27.4V		Weight	130g
LVD	10.7V	10.7V/21.4V		Size	70*110*23mm
LVR	12.6V	12.6V/25.2V		Window	105 * 67mm   (±0.5mm).
HVD	15.5V	15.5V/31.0V		Grade	IP30

CM20S 10A 20A Solar Charge Controller PWM

 

Features and Functions:

● Adopts industrial degree MCU SCM and particular software, reach intelligent control.

● PWM charging control mode, charge in high efficient.

● Battery reverse connection, over-voltage and low-voltage protections.

● Load output resume, output over-current, and output short-circuit protections.

● Solar panel short-circuit protection

● Battery open circuit protection

● High precision voltage recognition function

● LED indication for battery capacity

General Introduction

CM20S solar charge controller is especially designed by industrial degree MCU SCM with high-performance and excellent quality, and designed for home solar power system and solar power station.

Functions:

1) Battery management function:

Over-charge protection and over-discharge protection ensure the normal using and prolong the longevity of battery.

2) Temperature compensation function:

Auto adjust the setting data of battery management program control parameters to avoid the battery “under-voltage” in winter and “over-charge” in summer.

3) Multi-protections:

Battery reverse connection, over-voltage and low-voltage protections, solar panel short-circuit protection, auto. Resume output, and output short-circuit protections.

Connections

Connecting all parts correctly according to the following drawing, make sure polarity is right. The order is as follows.
Connect the controller with the battery first, then connect the solar panel, finally connect the load.
Disconnect from the controller: disconnect the load first, then solar panel, finally disconnect the batteries.
When connect the lines, make sure the “+” and “-” are not reversely connected.
Do not connect the line of battery to the solar panel terminal.
Do not connect any regulated power supply or charger to the solar panel terminal. 

Status Indication

  If the connection is correct, the indicators will show the capacity of the battery, and the load indicator will be on.
The charging indicator will be on when it is at charging state, and the charge indicator will flicker when the battery is charged full. When the battery is in low capacity, the battery indicator will flicker. It means you need to charge the battery now.
The load indicator on or off represents there is load output or there is no load output.

Model No. Parameters		CM20S-10A	CM20S-20A
Rated Voltage		12V / 24V
Rated Current		10A		20A
Over-Charge Protection		14.4V / 28.8V ± 0.2 Vdc
Over-Discharge	Cut-off	10.7V / 21.4V ± 0.2 Vdc
	Resume	12.6V / 25.2V ± 0.2 Vdc
Over-Voltage	Cut-off	16.5V / 33Vdc
	Resume	15.0V / 30.0 Vdc
Voltage Drop	Between input and batteries	<0.2 Vdc
	Between batteries and load	<0.2 Vdc
No Load Current Draw		<15 mA
Ambient Temperature		-10 ~ +55 °C
Altitude		≤5500m
Size (L*W*H: mm)		164*100*48
Weight (Kg)		0.39
Temp. Compensated factor		-4 mV / cell•°C

 

 

 

 

 

 

 

 

 

 

 

 

Protection Function

Protection item	Details
Batteries reverse polarity	the battery indicator will not be on if the battery is connected reversed
Solar module reverse polarity	If the solar module reverses polarity, the unit will function after correction.
Load over-current and short circuit protection	If the load draws current exceeding max. Discharge current or load short circuit, fuses will be blow.  Repair if necessary and replace the fuse with an equivalent.
Batteries open-circuit working Protection	When solar module is charging, and battery is open-circuit, the solar controller will limit voltage, so that the load will not be destroyed.

 

 

 

 

 

 

CM20D 10A 20A Solar Charge Controller ,BATTERY OPTION,VOLTAGE SETTABLE

CM20D controller is a kind of intelligent, multi-purpose solar charge and discharge controller. Fixed LCD display with a very friendly interface is used in this product; various control parameters can be flexibly set, fully meet your various application requirements.

 

This is a settable charge controllers:

1. Floating charge Voltage(HVD 13.3V-15V)
2. Recovery after under Voltage(LVD 11V-13.5V)
3.Under Voltage protection (RVD 9V-12.3V)
4.Load Mode(24hours,1-23hours,0hour)
5.Battery Option (GEL,LEAD-ACID,FLOODED)

Features:

Visual LCD graphic symbols	Simple button operation
Automatic Identification of System Voltage level	Intelligent PWM charging mode
Automatic Temperature Compensation (custom)	Adjustable charge-discharge control parameters
Settable Operating mode of Load	Battery reverse-discharge protection
Battery Low Voltage Disconnection (LVD)	Battery reverse connection protection
Over current protection.

P1: Digital parameters. 

P2£ºCharging indication. This symbol indicates that the  solar panel is charging the battery; without this symbol  means solar panel can not charge the battery because of low voltage. If the symbol is flickering, means the battery is fully

charged and has entered float charging state. 

P3£ºIndication for solar panel. This symbol indicates that the connection of solar panel is detected by controller; without this symbol means the connection of solar panel can not be detected, or there is no sunshine on the solar panel.

P4£º5 bars battery power indication.

P5: Discharging indication. This symbol indicates that controller is in output state, otherwise not in the output state. The flickering of this symbol indicates the damages of internal control devices.

P6£ºload indication. This symbol indicates that controller is in output state, otherwise not in the output state. The flickering of this symbol indicates overload or the damage of the load. 

P7£ºA stands for the unit of current; H stands for hour.

P8£ºV stands for the unit of voltage.

Type Parameters	CM20D				Type Parameters	CM20D
Rated current	10A24V	20A24V	30A24V		Charge and discharge voltage drop	£¼0.2V|£¼0.1V
Rated voltage	12V/24V Automatic Identification				Charging mode	PWM mode
Voltage of solar panel	≤50V				Temperature compensation	-4mV/Cell/℃£¨to be customized£©
Floating charge	13.8V/27.6V				Specification of the cables	≤5#  AWG  (6mm2)
Under-voltage protection	10.7V/21.4V				Working temperature	-20℃~60℃
Under-voltage recovery	12.6V/25.2V				Storage temperature	-30℃~70℃
Boost voltage	b01 sealed 14.4V/28.8V			(Duration£º2hours)	Temperature requested	≤90£¥,No condensation
	b02 Gel14.2V/28.4V				Dimension	88 mm×160 mm×37 mm
	b03Flooded 14.6V/29.2V				diameter of mounting hole	64 mm×150 mm --Φ5
Open circuit losses	≤13mA				Weight	230g
Remark

 

 

 

 

 

 

 

 

 

 

 

CY20A 20A Solar Charge Controller 12V 24V auto LCD display

The CY20A charge controllers is the highlight in the range.Use of the latest charging technologies combined with state of charge determination enable 
optimal battery maintenance.  A large display informs the user about all operating modes with the aid of symbols. The state of charge is represented visually in the form of a tank display. Data such as voltage, current and state of charge can also be displayed digitally 
as figures on the display..

Features:

1.Integrated data logger energy meter

2.Automatic detection of voltage

3.PWM control 

4Multistage charging technology

5.Automatic load re-connection

6.Temperature compensation

7.Overcharge protection

8.Deep discharge protection

9.Reverse polarity protection

10.Short circuit protection of load 

11.Reverse current protection at night

12.Load disconnection on battery over voltage

Description of LCD graphic symbol

Description of Button function

Data Sheet

Model	2024	3024	2048	3048
Rated current	20A	30A	20A	30A
Rated voltage	12/24V		48V
Max solar voltage	<50V		<100V
Low voltage disconnect	10.7/21.4V		42.8V
Low voltage reconnect	12.6/25.2V		50.4V
Float charge	13.7/27.4V		54.8V
Standby loss	<20mA
Charging mode	PWM
Temp compensation	-4mV/Cell/℃
Operating condition	-20℃~+60℃
Size/Weight	110*170*55/300g

CM3024 CM3048 12V 24V 48V Solar Charge Controller with LCD display light and timer control

 

This 30A controller is a kind of intelligent, multi-purpose solar charge and discharge controller. The family use the fixed LCD display, with a very friendly interface; various control parameters can be flexibly set, fully meet your various application requirements.

Features:
>>Image of LCD graphic symbol
>>Simple button operation
>>Automatic Identification System Voltage level
>>Intelligent PWM charge mode
>>Automatic Temperature Compensation
>>Adjustable charge-discharge control parameters
>>Settable Operating mode of Load
>>Overload, Short Circuit Protection
>>Remote monitoring and control function (custom)
>>Battery reverse-discharge protection
>>Battery Low Voltage Disconnection (LVD)
>>Battery reverse connection protection
>>Accumulated function of charge and discharge Ampere hours

Installation
1. Ready tools and cables. Encourage you to matching the right cables. Ensure that the current density<4mm2 that is conductive to reducing the line voltage drop. Recommended: 60A with 20mm2 cable. Check weather the installation sitescompliance with the relevant safety requirements. Please avoid the damp, dusty, there is a place flammable, explosive and corrosive gases use the controller to install.
2. Install the controller into a fixed vertical plane. See section 5 of the pore size and pore spacing. In order to ensure a good thermal control conditions, please set aside each 10cm below the controller space.
3. As shown on the right, connect the (1) Load, (2) Battery and (3) Solar Panel to the controller according to the order of (1) (2) (3). Pay attention to the load, battery, solar panel and controller of same polarity.
4. Put into the external temperature sensor on the left of the controller (probe port). The temperature sensor should be similar space with battery. (Otherwise, the controller will control the parameters of all wrong temperature compensation.)
5.If you have remote monitoring and control function, please insert one end of the included communication wire on the right of the controller (communication port), the other end to connect to The host computer.
Demolition: To prevent accidents, please order the demolition of solar panels, battery and load disconnect with controller.
Note:Battery polarity will not damage the controller, but you will have a load equipment security risks.

Specifications:

Model	CM2024Z	CM3024Z	CM2048Z	CM3048Z
Rated Current	20A	30A	20A	30A
Rated Voltage	12V/24V		48V
Open Circuit Voltage of solar panel	<=50V		<=100V
Low Voltage Disconnection(LVD)	10.7V/21.4V		42.8V
Float Voltage	13.8V/27.6V		55.2V
Low Voltage Reconnection(LVR)	12.5V/25.0V		50.0V
No load loss	<=30mA
Loop Voltage Drop	<=170mV
Charging Mode	PWM mode
Temperature Compensation	-4mV/Cell/'C
Installation cable area.	<=7#AWG (16mm2)
Operating Temperature	-10'C--60'C
Storage temperature	-30'C--70'C
Humidity requirements	<=90%,no condensation
Size	90 mmx188 mmx48 mm
Mounting hole spacing	60 mmx178 mm --dia5
weight	360g

 

CM50 50A Solar Charge Controller with LCD display 12V 24V 48V Solar Regulators

This 50A controller is a kind of intelligent, multi-purpose solar charge and discharge controller. The family use the fixed LCD display, with a very friendly interface; various control parameters can be flexibly set, fully meet your various application requirements.

Features:

Simple button operation

Intelligent PWM charge mode

Adjustable charge-discharge control parameters

Overload, Short Circuit Protection

Battery reverse-discharge protection

Battery reverse connection protection

Image of LCD graphic symbol

Automatic Identification System Voltage level

Automatic Temperature Compensation

Settable Operating mode of Load

Remote monitoring and control function (custom)

Battery Low Voltage Disconnection (LVD)

Accumulated function of charge and discharge Ampere hours

Model	CM5024Z	CM5048
Rated Current	50A
Rated Voltage	12V/24V	48V
Maximum Voltage of solar panel	50V	100V
Float Voltage	13.7V/27.4V	54.8V
Low Voltage Disconnection	10.7V/21.4V	42.8V
Low Voltage Reconnection	12.6V/25.2V	50.4V
No load loss	<30mA
loop voltage drop	<200mV
Charging Mode	¡¡PMW Mode
Temperature Compensation	¡¡-4mV/Cell/¡æ
Notes	¡¡Model suffix ¡°Z¡± represent automatic identify system voltage level£¬¡°T¡± represent controller with remote monitoring

Installation

Install£º
¢Ù Get ready for tools and cables. Advising you to matching the right cables. Ensure that the current density £¼4A/mm2 that is conductive to reducing the line voltage drop. Recommendation: 30A with 10mm2 cables. Check whether the installation sites compliance with the relevant safety requirements. Please avoid the damp, dusty, there is a place flammable, explosive and corrosive gases use the controller to install.
¢Ú Install the controller into a fixed vertical plane. See section 5 of the pore size and pore spacing. In order to ensure a good thermal control conditions, please set aside each 10cm below the controller space.
¢Û As shown on the right, connect the (1) Load, (2) Battery and (3) Solar Panel to the controller according to the order of (1) (2) (3). Pay attention to the load, battery, solar panel and controller of same polarity.
¢Ü Put the external temperature sensor into the left of the controller (probe port). The temperature sensor should be placed at the similar space of the battery. (Otherwise, the controller will control the parameters of all wrong temperature compensation.)
¢Ý If you have remote monitoring and control function, please insert one end of the included communication wire on the right of the controller (communication port), the other end to connect to the host computer.
Demolition: To prevent accidents, please order the demolition of solar panels, battery and load disconnect with controller.
Note£ºBattery polarity will not damage the controller, but you will have a load equipment security risks.

Installtion cable area	¡¡>3# AWG ( 25mm2 )
Operation temperature	-20¡æ ~ 50¡æ
storage temperature	-30¡æ ~ 70¡æ
Humidity requirement	¡¡<90% , no condensation
Size	¡¡130mm*188mm*62mm
Mounting hole spacing	¡¡90 mm 178 mm -- 5
Weight	590g

CM60 60A Solar Charge Controller with LCD display light and timer control

This 60A controller is a kind of intelligent, multi-purpose solar charge and discharge controller. The family use the fixed LCD display, with a very friendly interface; various control parameters can be flexibly set, fully meet your various application requirements.

Features:

Simple button operation

Intelligent PWM charge mode

Adjustable charge-discharge control parameters

Overload, Short Circuit Protection

Battery reverse-discharge protection

Battery reverse connection protection

Image of LCD graphic symbol

Automatic Identification System Voltage level

Automatic Temperature Compensation

Settable Operating mode of Load

Remote monitoring and control function (custom)

Battery Low Voltage Disconnection (LVD)

Accumulated function of charge and discharge Ampere hours

Model	CM6024Z	CM6048
Rated Current	60A
Rated Voltage	12V/24V	48V
Maximum Voltage of solar panel	50V	100V
Float Voltage	13.7V/27.4V	54.8V
Low Voltage Disconnection	10.7V/21.4V	42.8V
Low Voltage Reconnection	12.6V/25.2V	50.4V
No load loss	<30mA
loop voltage drop	<200mV
Charging Mode	¡¡PMW Mode
Temperature Compensation	¡¡-4mV/Cell/¡æ
Notes	¡¡Model suffix ¡°Z¡± represent automatic identify system voltage level£¬¡°T¡± represent controller with remote monitoring

Installation

Install£º
¢Ù Get ready for tools and cables. Advising you to matching the right cables. Ensure that the current density £¼4A/mm2 that is conductive to reducing the line voltage drop. Recommendation: 30A with 10mm2 cables. Check whether the installation sites compliance with the relevant safety requirements. Please avoid the damp, dusty, there is a place flammable, explosive and corrosive gases use the controller to install.
¢Ú Install the controller into a fixed vertical plane. See section 5 of the pore size and pore spacing. In order to ensure a good thermal control conditions, please set aside each 10cm below the controller space.
¢Û As shown on the right, connect the (1) Load, (2) Battery and (3) Solar Panel to the controller according to the order of (1) (2) (3). Pay attention to the load, battery, solar panel and controller of same polarity.
¢Ü Put the external temperature sensor into the left of the controller (probe port). The temperature sensor should be placed at the similar space of the battery. (Otherwise, the controller will control the parameters of all wrong temperature compensation.)
¢Ý If you have remote monitoring and control function, please insert one end of the included communication wire on the right of the controller (communication port), the other end to connect to the host computer.
Demolition: To prevent accidents, please order the demolition of solar panels, battery and load disconnect with controller.
Note£ºBattery polarity will not damage the controller, but you will have a load equipment security risks.

Installtion cable area	¡¡>3# AWG ( 25mm2 )
Operation temperature	-20¡æ ~ 50¡æ
storage temperature	-30¡æ ~ 70¡æ
Humidity requirement	¡¡<90% , no condensation
Size	¡¡130mm*188mm*62mm
Mounting hole spacing	¡¡90 mm 178 mm -- 5
Weight	690g