2014 New | MPPT solar controllers | I series solar controllers | S series solar controllers | C Sereis Solar Controllers | V Series Solar Controllers | G Z Sereis Solar Controller
WaterProof Solar Controllers | 48V Solar Controllers | Dual Battery Controllers | Solar Controllers With LED drivers | Accessories | User Manual

Oversea Warehouse - Australia - United States - United Kingdom

 

 

M10,M20,M30 10A,20A,30A PWM Solar Charge Controllers(MPPT-10,MPPT-20,MPPT-30)

 

Notcie: not true MPPT ,there is no large transformer coil inside


mppt30 solar controller inside

Package including:
1. 1pcs solar controller
2. 1pcs user manual
3. 1pcs temp sensor

This is a compatible MPPT charge controller PWM intelligent / efficient / energy saving, he not only has efficient MPPT controller charging function to automatically track the maximum power point, 10% -30% higher than the ordinary controller charging efficiency, also has standby energy saving, more than 30% energy than ordinary controller, the standby power consumption of only 10mA-15mA.

Product introduction

LCD screen display Battery reverse discharge protection
Easy operation interface Battery reverse polarity protection
MPPT+ PWM charging mode Battery under voltage protection
Parameter user can reset Overload Short-circuit protection
A key to restore the factory settings USB 5V charging (for 500mA) for mobile phone(Only for M30)
A key to open and close the load Automatic temperature compensation function

Solar LCD series a kind of intelligent,multi-purpose solar charge and discharge controller

mppt 30 display

Data Sheet

Parameters / Model

MPPT10

MPPT20

MPPT30

MPPT40

Maximum power current

12A

20A

30A

40A

Installation  Lin£¨mm2£©

4mm2

8mm2

10mm2

12mm2

Installation Line(AWG)

10(AWG)

8(AWG)

7(AWG)

6(AWG)

Weight

280g

300g

475g

480

Dimensions

143×89×46£¨mm£©

187*97*61£¨mm£©

System load loss

≤13mA

Loop Buck

≤100mV

Specification

Battery float voltage

13.8V£¨12V system£©/27.6V£¨24V system£©

Battery £¨under voltage) protection

10.6V£¨12V system£©/21.2V£¨24V system£©

Battery (under voltage) recovery voltage

12.6V£¨12V system£©/25.2V£¨24V system£©

Charge mode

MPPT+PWM MODE

Operating Temperature

-10℃~60℃

Storage Temperature

-30℃~70℃

Humidity requirements

≤90£¥, No condensation

Temperature compensation

-4mV/Cell/℃

Temperature Probe (built components)

NTC 100K  thermistats

Maximum open circuit voltage of the solar panel

18V-24V£¨12V system£©36V-48V£¨24V system)

Solar panels maximum open circuit voltage (V)

≤48V

(Cases) 12V system standard configuration 

The peak voltage of the solar cell panel

18V-25V

18V-25V

18V-25V

18V-25V

Peak power of solar cell panel

50W-130W

100W-260W

200W-380W

≤500W

Model

MPPT10

MPPT20

MPPT30

MPPT40

Battery standard voltage

12V

12V

12V

12V

Battery capacity 

≥100AH

≥200AH

≥300AH

≥400AH

Installation  Lin£¨mm2£©

4mm2

8mm2

10mm2

12mm2

Installation Line(AWG)

10(AWG)

8(AWG)

7(AWG)

6(AWG)

 

T10,T20 10A 20A Solar Charge Controller Dual timer

This is a three-time controller into the evening working time,an interval of rest of pause time,Dawn working time(morning light function), the user can according to their needs,set a different time.


A:time(evening working) B:time(pause working) C:time(dawn working)

This is a compatible MPPT charge controller PWM intelligent / efficient / energy saving, he not only has efficient MPPT controller charging function to automatically track the maximum power point, 10% -30% higher than the ordinary controller charging efficiency, also has standby energy saving, more than 30% energy than ordinary controller, the standby power consumption of only 10mA-15mA.

Product introduction

LCD screen display Battery reverse discharge protection
Easy operation interface Battery reverse polarity protection
MPPT+ PWM charging mode Battery under voltage protection
Parameter user can reset Overload Short-circuit protection
A key to restore the factory settings USB 5V charging (for 500mA) for mobile phone(Only for M30)
A key to open and close the load Automatic temperature compensation function


Dual Timer function

Data Sheet

Parameters / Model

T10

T20

T30

T40

Maximum power current

12A

20A

30A

40A

Installation  Lin£¨mm2£©

4mm2

8mm2

10mm2

12mm2

Installation Line(AWG)

10(AWG)

8(AWG)

7(AWG)

6(AWG)

Weight

280g

300g

475g

480

Dimensions

143×89×46£¨mm£©

187*97*61£¨mm£©

System load loss

≤13mA

Loop Buck

≤100mV

Specification

Battery float voltage

13.8V£¨12V system£©/27.6V£¨24V system£©

Battery £¨under voltage) protection

10.6V£¨12V system£©/21.2V£¨24V system£©

Battery (under voltage) recovery voltage

12.6V£¨12V system£©/25.2V£¨24V system£©

Charge mode

MPPT+PWM MODE

Operating Temperature

-10℃~60℃

Storage Temperature

-30℃~70℃

Humidity requirements

≤90£¥, No condensation

Temperature compensation

-4mV/Cell/℃

Temperature Probe (built components)

NTC 100K  thermistats

Maximum open circuit voltage of the solar panel

18V-24V£¨12V system£©36V-48V£¨24V system)

Solar panels maximum open circuit voltage (V)

≤48V

(Cases) 12V system standard configuration 

The peak voltage of the solar cell panel

18V-25V

18V-25V

18V-25V

18V-25V

Peak power of solar cell panel

50W-130W

100W-260W

200W-380W

≤500W

Model

T10

T20

T30

T40

Battery standard voltage

12V

12V

12V

12V

Battery capacity 

≥100AH

≥200AH

≥300AH

≥400AH

Installation  Lin£¨mm2£©

4mm2

8mm2

10mm2

12mm2

Installation Line(AWG)

10(AWG)

8(AWG)

7(AWG)

6(AWG)


S10I,S20I,S30I 10A-30A Solar Controller(Battery Option,Voltage settable)

The controller is for off-grid solar system,especially in solar lighting system and protects the battery from being over charged by the solar module and over dischargerged by the loads.The charging process has been optimized for long battery life and improved system performance.The comrehensive self-diagnostics and electronic protection functions can prevent damaged from installation mistakes or system faults.

 

 

Three battery type option:

Gel,Sealed,Flooded

Settable:

Float charging voltage;

Low voltage reconnect voltage;

Low voltage discounnect voltage;

Load start-up delay;

Optical sensitivity.

Four load working modes:

Pure lighting control

lighting control &timing control,

hand operation

debug mode.

Features:

12/24V automatic recognition

¡¤High efficient Series PWM charging, increase the battery lifetime and improve the solar system performance.

¡¤Use MOSFET as electronic switch, without any mechanical switch

¡¤Widely used, automatically recognize day/night.

¡¤Digital LED menu, only one key solve all setting simply

¡¤Intelligent timer function with 1-15 hours option

¡¤Unique dual timer function, enhance the flexibility of street light system.

¡¤Gel, Sealed and Flooded battery type option.

¡¤Adopt temperature compensation, correct the charging and discharging parameters automatically and improve the battery lifetime.

¡¤Electronic protection: Overheating, over charging, over discharging,

overload, and short circuit.

¡¤Reverse protection: any combination of solar module and battery.

Settings

. Load Control Settings

1. Dusk to Dawn

When solar module voltage goes below the point of NTTV (Night Time Threshold Voltage) at sunset, the controller will recognize the starting voltage and turn on the load after 10 minutes delay. When solar module voltage goes above point of DTTV (Day Time Threshold Voltage), the solar controller will recognize the starting voltage and turn off the load after 10 minutes delay.

2. Light ON + Timer

When solar module voltage goes below the point of NTTV (Night Time Threshold Voltage) at sunset; the solar controller will recognize the starting voltage and turn on the load after 10 minutes delay. The load will be on for several hours which users set through LED digital tube. The controller has dual timer function. Please refer to table 4-5 ¨DLoad Work Mode Setting¡¬.

3. Test mode

This mode is the same as Dusk to Dawn. But there is no 10 minutes delay when controller recognizes the starting voltage. When below the starting voltage, the controller will turn on the load, if higher, it will turn off load.

The test mode makes it easy to check the system installation.

4. ON/OFF mode

This mode is to turn ON and OFF the load by manual.

A.Load Work Mode Setting

When the led digital tube is not display, Press the setting button "Key" more than 5 seconds , and keep on press it once more,led digital tube will be changed once among

¡¾0¡¿ ¡¾Load work mode¡¿
¡¾b1¡¿ ¡¾Battery type¡¿
¡¾J0¡¿ ¡¾Load start-up delay¡¿
¡¾S5¡¿ ¡¾Optical sensitivity¡¿
¡¾F0¡¿ ¡¾Float charging voltage¡¿
¡¾H0¡¿ ¡¾Low voltage reconnect voltage¡¿
¡¾q0¡¿

¡¾Low voltage disconnect voltage¡¿

¡¾8.8.¡¿ ¡¾Restore factory Settings¡¿.

B.Work mode led digital tube display£º

Press the setting button "KEY" more than 5 secondsand setting indicators will be changed once among ¡¾0¡¿¡¾b1¡¿¡¾J0¡¿¡¾S0¡¿¡¾F0¡¿¡¾H0¡¿¡¾q0¡¿¡¾8.8.¡¿.

When you want to change`s setting indicator is on, press the setting button for more than 5 seconds till the LED digital tube flashes. Then press the setting button till the desired number appears according to the following table. The setting is finished when the digital tube stop flashing.

work mode Table 4-5

Led

Ranges

Function

Describe

0

0-17

Load work mode

0= Dusk to Dawn (Default)

1-15= Light ON + Timer

16= ON/OFF mode

17= Test mode Default

b1

b1-b3

Battery type

B1= Sealed lead acid battery (Default)

B2= Flooded battery

B3= Gel battery

J0

J0-J9

Load start-up delay

J0 10min (Default)

J1=increase 10min

J9=increase 90min

S5

S0-S9

Optical sensitivity

S5(5v load on,6V load off) Default

S4=all reduce 0.2V 4.8V load on,5.8V load off

S6=all increase 0.2V 5.2V load on,6.2V load off

F0

F0

-F9

F0.

-F9.

Float charging voltage

F0£¨13.8V£© (Default)

F1= increase 0.1V

F9= increase 0.9V

F1£®= reduce 0.1V

F9£®= reduce 0.9V

H0

H0

-H9

H0.

-H9.

Low voltage reconnect voltage

H0£¨12.6V£© (Default)

H1=increase 0.1V

H9=increase 0.9V

H1£®=reduce 0.1V

H9£®=reduce 0.9V

q0

q0

-q9

q0.

-q9.

Low voltage disconnect voltage

q0£¨11.1V£© (Default)

q1= increase 0.1V

q9= increase 0.9V

q1£®= reduce 0.1V

q9£®= reduce 0.9V

8.8.

8.8.

Restore factory Settings

Restore factory Settings

Load work mode ¡¾0¡¿ Table 4-6

Describe

LED digital No.

Dusk to Dawn, Load will be on all night

0

Load will be on for 1 hour after ten minutes delay since sunset

1

Load will be on for 2 hour after ten minutes delay since sunset

2

Load will be on for 3 hour after ten minutes delay since sunset

3

Load will be on for 4 hour after ten minutes delay since sunset

4

Load will be on for 5 hour after ten minutes delay since sunset

5

Load will be on for 6 hour after ten minutes delay since sunset

6

Load will be on for 7 hour after ten minutes delay since sunset

7

Load will be on for 8 hour after ten minutes delay since sunset

8

Load will be on for 9 hour after ten minutes delay since sunset

9

Load will be on for 10 hour after ten minutes delay since sunset

10

Load will be on for 11 hour after ten minutes delay since sunset

11

Load will be on for 12 hour after ten minutes delay since sunset

12

Load will be on for 13 hour after ten minutes delay since sunset

13

Load will be on for 14 hour after ten minutes delay since sunset

14

Load will be on for 15 hour after ten minutes delay since sunset

15

ON/OFF mode

16

TEXT mode

17

Data Sheet:

Description

Parameter

Nominal System Voltage

12 / 24VDC Auto work

Battery Voltage Range

6-36V

Rated Battery Current

10A,20A,30A

Charge Circuit Voltage Drop

¡Ü0.26V

Discharge Circuit Voltage Drop

¡Ü0.15V

Self-consumption

¡Ü6mA

Threshold Voltage Parameters

Description

Parameter

NTTV (Night Time Threshold Voltage)

5V; x2/24V

DTTV (Day Time Threshold Voltage)

6V; x2/24V

Temperature Compensation Coefficient

Description

Parameter

Temperature Compensation (TEMPCO)*

-25mV/¡æ/12V£¨25¡æ ref£©


* Compensation of equalize, boost, float and boost reconnect voltage


Battery Voltage Parameters (temperature at 25¡æ)

Charging setting

Sealed

Flooded

Gel

Over voltage disconnect

15.5V;x2/24V

Charging limit voltage

15.0V;x2/24V

Equalize charging voltage

14.6V;¡Á2/24V

14.8V;¡Á2/24V

14.4V;¡Á2/24V

Boost charging voltage

14.4V;¡Á2/24V

14.6V;¡Á2/24V

14.2V;¡Á2/24V

Float charging voltage

13.8V;x2/24V
Boost reconnect charging voltage
13.2V;x2/24V
Low Voltage reconnect voltage
12.6V;x2/24V
Under Voltage warning reconnect voltage
12.2V;x2/24V
Unver voltage warning voltage
12V;x2/24V
Low voltage disconnect voltage
11.1V;x2/24V
Discharge limit voltage
10.8V;x2/24V
Equalize duration
60min

Boost duration

60min

Environmental parameters

Environmental parameters

Parameter

Working temperature

-35¡æ to +55¡æ

Storage temperature

-35¡æ to +55¡æ

Humidity

10%-90% NC

Enclosure

IP30

 

LS10 LS20 10A 20A Solar Controller(Battery Option)

This solar controller adopts the most advanced digital technique and operates fully automatically. 

The Pulse Width Modulation (PWM) battery charging can greatly increase the lifetime of battery.

Application£º

Ideal for off-grid solar system that loads are normally on or controlled by manual.

¡ï Solar traffic system 

¡ï Solar home system

¡ï Unattended CCTV Equipment 

¡ï Wild automatic detection equipment

 

Features: 
·High efficient Series PWM charging 
·Use MOSFET as electronic switch 
·Gel, Sealed and Flooded battery type option 
·Temperature compensation 
·LED indicators indicate battery voltage state

Electronic Protections: 
·Overheating 
·Over discharging 
·Over charging 
·Load overload 
·Load short circuit 
·PV short circuit 
·PV reverse polarity 
·Battery reverse polarity

Electrical parameters

LS10

LS20

Nominal System Voltage

12 / 24VDC auto work

Rated Battery Current

10A

20A

Max. Battery Voltage

32V

Charge Circuit Voltage Drop

≤0.26V

Discharge Circuit Voltage Drop

≤0.15V

Self-consumption

≤6mA

Overall dimension

140 x 65 x 34mm

144 x 75x 45mm

Terminal

4mm2

10mm2

Net weight

0.15kg

0.25kg

Working temperature

-35¡æ to +55¡æ

Humidity

10%-90% NC

Enclosure

IP30

 

Battery Voltage Parameters (temperature at 25¡æ)

Battery charging setting

Gel

Sealed

Flooded

Equalize Charging Voltage

——

14.6V;x2/24V

14.8V;x2/24V

Boost Charging Voltage

14.2V;x2/24V

14.4V;x2/24V

14.6V;x2/24V

Float Charging Voltage

13.8V;x2/24V

13.8V;x2/24V

13.8V;x2/24V

Low Voltage Reconnect Voltage

12.6V;x2/24V

12.6V;x2/24V

12.6V;x2/24V

Low Voltage Disconnect Voltage

11.1V;x2/24V

11.1V;x2/24V

11.1V;x2/24V

Equalize Duration

——

2 hours

2 hours

Boost Duration

2 hours

2 hours

LS1024B,LS2024B,LS3024B 10A-30A Solar Controllers

All the models adopt aluminum heat sink which enables the reliability in high temperature enviroments.RS-485 connects to a remote meter or PC for real-time monitoring, custom setting and control etc.

 

Features:

¡¤Three system voltage configuration : 12V, 24V or 12V/24V auto work
¡¤High efficiency PWM charging with temperature compensation
¡¤3 LEDs shows PV charging, battery and load status
¡¤External temperature sensor interface
¡¤RS-485 bus communication
¡¤Open standard Modbus communication protocol
¡¤Software update function
More powerful function via MT50 or PC
¡¤Diversified load control modes : Manual, Light ON/OFF, Light ON+ Timer, Time Control
¡¤Battery type selection: Gel, sealed, flooded and User type
¡¤Real-time monitor
¡¤Programmable parameters
¡¤LVD or SOC load disconnect function
¡¤Energy statistics function

Electronic Protections£º
¡¤PV short circuit
¡¤PV reverse polarity
¡¤Battery overcharge
¡¤Battery over discharge
¡¤Battery reverse polarity
¡¤Load short circuit
¡¤Load overload
¡¤Overheating

Electrical parameters

LS1024B

LS2024B

LS3024B

Nominal System Voltage

12 / 24V auto work

Rated Battery Current

10A

20A

30A

Maximumbatteryvoltage

50V

Grounding

Common positive

Self-consumption

8.4mA(12V)£¬7.8mA(24V)

Temp. compensation

-3mV/¡æ/2V£¨25¡æref£©

Equalize charging voltage

Sealed: 14.6V, Flooded: 14.8V, User-defined: 9~17V

Boost charging voltage

Gel: 14.2V, Sealed: 14.4V, Flooded: 14.6V, User-defined: 9~17V

Float charging voltage

Gel /Sealed /Flooded: 13.8V, User-defined: 9~17V

Low voltage reconnect voltage

Gel /Sealed /Flooded: 12.6V, User-defined: 9~17V

Low voltage disconnect voltage

Gel /Sealed /Flooded: 11.1V, User-defined: 9~17V

Working temp.

-35¡æ~+55¡æ

Humidity

¡Ü95% (NC)

Enclosure

IP30

Dimension

138.6x69.3x37mm

159.6x81.4x47.8mm

200.6x101.3x57mm

Terminal

4mm2

10mm2

10mm2

Net weight

0.13kg

0.3kg

0.5kg

 

 

Click hear to chat online

Copyright© YSmart Technology Co.,Ltd .2009-2014 Powered by ChinaSolarRegulator.com